Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
What're your thoughts on Tools You Need to Install a New Bathtub ?

Installing a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is conveniently easily accessible, the job can move speedily; if you have to open a wall surface to get rid of the old bathtub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require a helper to leave the old bathtub and also embeded in the new one. Make sure you have actually qualified on your own for the job as well as are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This article will certainly help you mount a brand-new tub in your bathroom if you have actually currently purchased a new bathtub as well as don't require to transform the arrangement of your previous water pipelines.
Your tools as well as material list need to consist of the following:
Getting ready for the Setup
Firstly, the supporting framework supplied with the bathroom must be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps system to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing compound.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the needed placement. The wood boards are useful in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and changing the feet on the bathtub till the level reads degree.
To mount taps, fit all-time low of the furthest versatile faucet port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bath tub as well as likewise check the overflow outlet and also the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bathtub must wait till the bathtub has been used a minimum of when as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making sure that the washers are in location between the faucet and the sink. Secure the tap in position with the producer supplied backnut. Once the faucet is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap ports. The previous kind should be connected to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a rigid seal, creating the water to pass through the wall between the bath as well as the tiling, leading to difficulties with wetness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and also can securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to sealing, to allow for the motion experienced when the tub is in use. The sealant can crack relatively early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly offered on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that article on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. Those who enjoyed reading our article if you please make sure you remember to pass it around. Thanks for taking the time to read it.
Need urgent help? Reach. Report this page